{"id":3317,"date":"2023-05-18T16:56:56","date_gmt":"2023-05-18T08:56:56","guid":{"rendered":"https:\/\/www.hginstrument.com\/?p=3317"},"modified":"2023-05-19T16:25:18","modified_gmt":"2023-05-19T08:25:18","slug":"menu-function-and-operation-introduction-for-sypm-23-pressure-transmitter","status":"publish","type":"post","link":"https:\/\/www.hginstrument.com\/es\/menu-function-and-operation-introduction-for-sypm-23-pressure-transmitter\/","title":{"rendered":"Menu function and operation introduction of SYPM-23 Pressure Transmitter"},"content":{"rendered":"

Menu function and operation introduction for SYPM-23 Transmisor de presi\u00f3n<\/a><\/strong><\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n
Menu name<\/td>\nFunction description<\/td>\n<\/tr>\n
POINT<\/strong><\/td>\nAt menu interface “POINT”( “POINT” flickers), press M button to enter its parameter setting interface, press Z button to select decimal digits. ( select range: 0, 1, 2, 3, 4 )<\/p>\n

0: No decimal digit.\u00a0 1: One decimal digit.\u00a0 2: Two decimal digits<\/p>\n

3: Three decimal digits\u00a0 4: Four decimal digits<\/p>\n

After complete setting, press M button to save, then press S button return menu interface “POINT”, then press S button return measuring status.<\/td>\n<\/tr>\n

UNIT<\/strong><\/td>\nAt menu interface “UNIT”, press M button to enter its parameter setting interface, press Z button to select engineering unit. ( Selectable unit: Mpa, mmH2O, PSI, Bar, mBar, Pa, Kg\/cm2, Kpa, mA, %, mm, M, mH2O )<\/p>\n

After complete setting, press M button to save, then press S button return menu interface “POINT”, then press S button return measuring status.<\/td>\n<\/tr>\n

LOWER<\/strong><\/td>\nMenu “LOWER” is used to set up the value which is corresponding to 4 mA.<\/p>\n

At menu interface ” LOWER “, press M button to enter its parameter setting interface, at this time, the rightmost digit is flickering, press Z can select number from 0 to 9, press S button can shift cursor.<\/p>\n

When the cursor is flickering on the leftmost digit, press S, the symbol “-” flickers, press Z can select minus sign or positive sign. ( If flickering rate of “-” speeds up, it means minus sign is selected. If flickering rate of “-” is slow, it means positive sign is selected, positive sign does not display )<\/p>\n

When the sign “-” flickers, press S, the decimal point flickers, press Z can select location of the decimal point.<\/p>\n

After complete setting, press M to save, then press S return menu interface ” LOWER “, then press S button return measuring status.<\/td>\n<\/tr>\n

UPPER<\/strong><\/td>\nMenu “UPPER” is used to set up the value which is corresponding to 20 mA.<\/p>\n

Setting method is the same as that for Menu “LOWER”. ( The parameter of menu “UPPER has no sign bit )<\/td>\n<\/tr>\n

DAMP<\/strong><\/td>\nMenu “DAMP” is used to set up damping time, unit is “S” (second).<\/p>\n

Valid set range: 0 ~ 64 seconds<\/p>\n

Setting method is the same as that for Menu “LOWER”. ( The parameter of menu “DAMP” has no sign bit )<\/td>\n<\/tr>\n

LOOP FIx<\/strong><\/td>\nMenu “LOOP Fix” is used to set up fixed output current.<\/p>\n

At menu interface ” LOOP Fix “, press M button to enter its parameter setting interface, press Z button to select output current. ( selectable output current : 3.<\/strong>800mA, 4.<\/strong>000mA, 8.<\/strong>000mA, 12.<\/strong>000mA, 16.<\/strong>000mA, 20.<\/strong>000mA, 20.<\/strong>800mA )<\/td>\n<\/tr>\n

CLR ZERO<\/strong><\/td>\nMenu “CLR ZERO” is used for calibration pressure Zero point. Operation as follow:<\/p>\n

> Make the pressure transmitter be under the condition of zero pressure.<\/p>\n

> Power on the pressure transmitter.<\/p>\n

> At menu interface ” CLR ZERO “, press M button to enter its parameter setting interface, use Z button and S button to set value into 0.<\/strong>0, then press M to save.<\/p>\n

> Press S button return menu interface ” CLR ZERO “, then press S button return measuring status.<\/td>\n<\/tr>\n

DENSITY<\/strong><\/td>\nDensity setting is only valid for the condition that the selected engineering unit is mm and M.<\/p>\n

Setting method is the same as that for menu “DAMP”. ( density unit is g\/cm3 )<\/td>\n<\/tr>\n

ALARM<\/strong><\/td>\nMenu “ALARM” is used for out of range fault alarm.<\/p>\n

At menu interface ” ALARM “, press M button to enter its parameter setting interface, press Z button to select Low limit alarm or High limit alarm. ( select range: 0, 1 )<\/p>\n

0: high limit alarm (20.8mA),\u00a0 1: Low limit alarm (3.8mA)<\/p>\n

After complete setting, press M to save, then press S return menu interface ” LOWER “, then press S button return measuring status.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>","protected":false},"excerpt":{"rendered":"

Menu function and operation introduction for SYPM-23 Pressure Transmitter<\/p>","protected":false},"author":1,"featured_media":3044,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":[],"categories":[2130],"tags":[],"acf":[],"_links":{"self":[{"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/posts\/3317"}],"collection":[{"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/comments?post=3317"}],"version-history":[{"count":0,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/posts\/3317\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/media\/3044"}],"wp:attachment":[{"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/media?parent=3317"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/categories?post=3317"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.hginstrument.com\/es\/wp-json\/wp\/v2\/tags?post=3317"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}