{"id":1986,"date":"2021-09-02T16:02:00","date_gmt":"2021-09-02T08:02:00","guid":{"rendered":"http:\/\/201230ip92c2.adwebcloud.com\/?post_type=product&p=1986"},"modified":"2021-10-12T14:45:01","modified_gmt":"2021-10-12T06:45:01","slug":"hgppc-68-portable-pressure-calibrator-hydraulic","status":"publish","type":"product","link":"https:\/\/www.hginstrument.com\/it\/calibration-instrument\/hgppc-68-portable-pressure-calibrator-hydraulic\/","title":{"rendered":"HGPPC-68 Calibratore di pressione portatile (idraulico)"},"content":{"rendered":"

Dati tecnici:<\/strong><\/p>\n

\u25cf Pressure source medium in pressure producing system is purified water or clear water without solid particle or corrosivity
\n\u25cf Pressure source range:\u00a0 0 ~ 60 Mpa
\n\u25cf Resolution: pressure 1 Pa, current 1 \u03bcA
\n\u25cf Current range: 0 – 22 mA
\n\u25cf Feedback power output: 24VDC
\n\u25cf Accuracy: 0.1%FS, 0.05%FS(pressure), 0.05%(current)
\n\u25cf Display pressure and current simultaneously
\n\u25cf Over range ability: 1.2 – 1.5 times F.S
\n\u25cf With built-in rechargeable battery: 6V DC, very convenient for operating on site where power supply is not available. Full charge time is about 12 hours if battery is power off.
\n\u25cf Working time of battery
\n– Continuous working but not supply power 24VDC:\u00a0 \u00a016 hours
\n– Continuous working and supply power 24VDC:\u00a0 8 hours
\n– Intermittent working:\u00a0 about 18 hours
\n\u25cf Ambient temperature: 5 – 55 Deg.C
\n\u25cf Humidity: \u226480%RH
\n\u25cf 2-wire wiring circuit in the back panel for inputting current 4 -20mA
\n\u25cf Net weight: 2.5Kg
\n\u25cf Power dissipation: 2 – 3VA<\/p>\n

 <\/p>\n

Appearance introduction:<\/strong><\/p>\n

\"hgppc<\/p>\n

(1) Fine tuning<\/strong>: also called trim handle, screw it to get the exact pressure value you wanted
\nNote: Fine tuning can not be screwed by using the brute force when it has reached its minimum or maximum, otherwise the fine tuning will be damaged.
\n(2) Handle pump<\/strong>: repeatedly pull out and press down this handle pump to produce a certain pressure, the maximum pressure produced by this handle pump should not exceed 2.5 – 3 Mpa, otherwise the built-in pressure sensor might be short life or damaged, this handle pump\u2019s function is equal to coarse tuning.
\n(3) Relief valve<\/strong>:
\nBefore using handle pump to produce pressure, you should close relief valve (screw the valve clockwise).
\nWhen the pressure exceeds the upper limit of range, you should open the relief valve (screw the valve anticlockwise) till the pressure is in the range then close valve.
\nIf instrument is not used, the relief valve should be at open status.
\n(4) Interfaccia di uscita della pressione<\/strong>: thread M20x1.5, used to connect to pressure gauge or pressure transmitter.
\n(5) Stud<\/strong>: used to prevent dust particles from entering the pressure producing system when calibrator is not used, also can tighten it on the pressure output interface to check the gas tightness of pressure producing system when producing pressure.
\n(6) Exhaust pipe<\/strong>: in order to make calibrator work normally, the air in the pressure producing system should be eliminated by liquid. (Exhaust pipe is only for Hydraulic type)
\n(7) Battery charging socket
\n(8) 24V DC+:<\/strong> Power supply produced by calibrator
\n(9) Common grounding<\/strong>
\n(10) Current input socket: connect to the \u201cI+ \u201c of pressure transmitter.
\n(11) Water cup connection interface:<\/strong> for connecting water cup to inject pressure source medium– purified water, if calibrator is not used, the water cup should be disassembled, then use a cap or something else to cover this connection interface to prevent dust from entering the pressure producing system. (Water cup is only for Hydraulic type)<\/p>\n

\"hgppc<\/p>\n

(12) Calibrator power switch<\/strong>: \u201cI\u201d means powered on, \u201c0\u201dmeans powered off.<\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>","protected":false},"excerpt":{"rendered":"

HGPPC-68 Portable Hydraulic Pressure Calibrator\u00a0is used to calibrate pressure transmitters and pressure gauges.<\/p>\n

Range:\u00a0 0 ~ 60 Mpa<\/p>","protected":false},"featured_media":1987,"comment_status":"closed","ping_status":"closed","template":"","meta":[],"product_cat":[1806,1851],"product_tag":[],"acf":[],"_links":{"self":[{"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/product\/1986"}],"collection":[{"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/comments?post=1986"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/media\/1987"}],"wp:attachment":[{"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/media?parent=1986"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/product_cat?post=1986"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/www.hginstrument.com\/it\/wp-json\/wp\/v2\/product_tag?post=1986"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}